By default, however, the Routing and Remote Access service is turned off. Click the server icon that matches the local server name in the left pane of the console. If the icon has a red circle in the lower-left corner, the Routing and Remote Access service hasn't been turned on. If the icon has a green arrow pointing up in the lower-left corner, the Routing and Remote Access service has been turned on.
If the Routing and Remote Access service was previously turn on, you may want to reconfigure the server. To reconfigure the server:. Click to select VPN or Dial-up depending on the role that you intend to assign to this server. In the IP Address Assignment window, click Automatically if a DHCP server will be used to assign addresses to remote clients, or click From a specified range of addresses if remote clients must only be given an address from a pre-defined pool.
In most cases, the DHCP option is simpler to administer. However, if DHCP isn't available, you must specify a range of static addresses. Click Next to continue. If you clicked From a specified range of addresses , the Address Range Assignment dialog box opens. Click New. Type the first IP address in the range of addresses that you want to use in the Start IP address box. Windows calculates the number of addresses automatically.
Accept the default setting of No, use Routing and Remote Access to authenticate connection requests , and then click Next to continue. For the remote access server to forward traffic properly inside your network, you must configure it as a router with either static routes or routing protocols, so that all of the locations in the intranet are reachable from the remote access server.
The number of dial-up modem connections is dependent on the number of modems that are installed on the server. For example, if you have only one modem installed on the server, you can have only one modem connection at a time. The number of dial-up VPN connections is dependent on the number of simultaneous users whom you want to permit. By default, when you run the procedure described in this article, you permit connections.
To change the number of simultaneous connections, follow these steps:. You can also configure a static IP address pool. Configure the dial-in properties on user accounts and remote access policies to manage access for dial-up networking and VPN connections. To grant dial-in access to a user account if you're managing remote access on a user basis, follow these steps:. If the VPN server already permits dial-up networking remote access services, do not delete the default policy.
Instead, move it so that it is the last policy to be evaluated. To set up a connection to a VPN, follow these steps. To set up a client for virtual private network access, follow these steps on the client workstation:. Because there are several versions of Microsoft Windows, the following steps may be different on your computer.
If they are, see your product documentation to complete these steps. Click Create a new connection under Network Tasks , and then click Next. Click Connect to the network at my workplace to create the dial-up connection. Type a descriptive name for this connection in the Company name dialog box, and then click Next. Click Do not dial the initial connection if the computer is permanently connected to the Internet.
Click Next. Click Anyone's use if you want to permit any user who logs on to the workstation to have access to this dial-up connection. Click My use only if you want this connection to be available only to the currently logged-on user.
Click Properties to continue to configure options for the connection. To continue to configure options for the connection, follow these steps:. Click Start , point to Connect to , and then click the new connection. Hi healee,. Thanks for posting here. Till Windows , routing and remote access server i. RRAS and Windows firewall didn't co-exist. And we are also not suggest to multihomed a domain controller or set it direct facing internet without protection and will suggest use a dedicate server to host VPN service at edge of internal network.
For more information please refer to the article below:. RRAS static packet filters - do's and don'ts. Tiger Li. Thanks for update. Office Office Exchange Server. Not an IT pro? You'll need to identify which interface will act in this capacity. On the VPN server in my lab for this exercise, I have two interfaces. The first interface's address is Since this server is in my lab, it does not have a true public address.
However, for the purposes of this example, I'll use the Below the interface list, you'll notice a check box indicating that static packet filters can be applied to this interface to allow VPN traffic only. I recommend that you enable this feature, especially if this interface is outside the corporate firewall. To access resources on the internal network, the remote client needs an IP address that is allowed to do so.
First, you can use an existing DHCP server on your network after making sure that it is configured properly. Second, you can provide the VPN server with a range of addresses that it can dole out to the clients. I prefer the second method, because it makes me feel a little more in control. I have to provide a range of addresses, and it allows me to quickly determine just by looking at a list of IP connections to a server if they are internal or VPN clients.
If you choose this method and are using addresses from the same space as your internal network, make sure you exclude the range you choose from any DHCP scopes you've defined on other DHCP servers to prevent addressing conflicts. For this article, I'll choose this option.
Because I'm assigning addresses from a specified pool, the pool or pools must be set up, which I'll do on the Address Range Assignment screen. In this example, that network is To add a range, click the New button. You need to supply the starting address of the range and either the ending address or the number of addresses you would like in the pool.
For this example, I'll create a range of 25 addresses from A key aspect in providing remote access services is authentication. Without it, anyone can access your internal network as long as they can get to your VPN server. If you don't have one, you can just let the RRAS services handle the authentication. After this step, the wizard will configure RRAS based on the parameters you specified. You should then see a green arrow next to your local server on the RRAS screen indicating that the service is active.
Rather, an administrator needs to enable this privilege for each user who needs it. Next, right-click on a user object and choose Properties. Click Apply or OK to continue.
0コメント